A & C Metals Logo
 
steel tubing
 
   
""
STEEL HYDRAULIC-LINE TUBING
Cold Drawn Welded
 Top
Produced To O.D. and I.D. Dimensions
Soft Annealed—Oiled
SAE J525—Electronically tested
Standard Lengths: 20 Ft. Random
   O.D. & Ga. Wall I.D. Lbs.
Per Ft.		 Est. Lbs.
Per 20 Ft.
1/8 x 22 .028   .069   .0290          .5800 * §
3/16 x 20 .035   .118   .0572   1.144 *
1/4 x 22 .028   .194   .0664 1.328
20 .035   .180   .0804 1.608
18 .049   .152   .1052 2.104
5/16 x 20 .035   .243   .1039 2.078
18 .049   .215   .1382 2.764
3/8 x 20 .035   .305   .1271 2.542
18 .049   .277   .1706 3.412
16 .065   .245   .2152 4.304
1/2 x 20 .035   .430   .1738 3.476
18 .049   .402   .2360 4.720
16 .065   .370   .3020 6.040
14 .083   .334   .3696 7.392
5/8 x 20 .035   .555   .2205 4.410
18 .049   .527   .3014 6.028
16 .065   .495   .3888 7.776
14 .083   .459   .4805 9.610
13 .095   .435   .5377 10.75    
3/4 x 20 .035   .680   .2673 5.346
18 .049   .652   .3668 7.336
16 .065   .620   .4755 9.510
14 .083   .584   .5913 11.83    
13 .095   .560   .6646 13.29    
11 .120   .510   .8074 16.15    
7/8 x 16 .065   .745   .5623 11.25    
14 .083   .709   .7021 14.04    
13 .095   .685   .7914 15.83    
12 .109   .657   .8917 17.83    
1"      x 18 .049   .902   .4977 9.954
16 .065   .870   .6491 12.98    
14 .083   .834   .8129 16.26    
13 .095   .810   .9182 18.36    
12 .109   .782 1.037   20.74    
11 .120   .760 1.128   22.56    
1-1/4 x 18 .049 1.152   .6285 12.57    
16 .065 1.120   .8226 16.45    
14 .083 1.084 1.035   20.70    
13 .095 1.060 1.172   23.44    
12 .109 1.032 1.328   26.56    
11 .120 1.010 1.448   28.96    
1-1/2 x 16 .065 1.370   .9962 19.92    
13 .095 1.310 1.426   28.52    
11 .120 1.260 1.769   35.38    
2"     x 16 .065 1.870 1.343   26.86    
13 .095 1.810 1.933   38.66    
11 .120 1.760 2.409   48.18    
2-1/4 x 16 .065 2.120 1.517   30.34    
2-1/2 x 16 .065 2.370 1.690   33.80    
 * Produced to O.D. and Wall dimensions
§ SAE J 524 Seamless
 
 
1 Disclaimer: All technical data throughout this site is given only as an indication of what may be expected and should under no circumstances be used in specifying the raw materials. The technical data throughout this site has been obtained from a variety of sources we believe to be accurate, but is NOT GUARANTEED. A & C Metals - Sawing, Inc. assumes no liability whatsoever for the use of or reliance upon this information.
  ©   A & C Metals - Sawing, Inc. — All Rights Reserved. | Terms and Conditions | Privacy Policy